Top 16 CAN Transceiver Manufacturers

Table of Contents

Texas Instruments, NXP, Infineon, Analog Devices, and Microchip are useful starting points when comparing CAN transceiver manufacturers. The shortlist also includes automotive interface specialists, Chinese analog IC suppliers, and manufacturers serving isolated industrial networks or aerospace applications.

For a buyer, the choice comes down to the exact device. The quoted part still needs to match your CAN FD data rate, logic voltage, wake-up behavior, and qualification requirements. Even two eight-pin devices can need different board connections.

At DuoLink Electronics, we support component inquiries and BOM quotations as an independent supplier. Our integrated circuits range includes interface devices, so an inquiry should start with the full manufacturer part number and the application’s approved requirements. The manufacturers below offer different routes to that shortlist.

The numbering follows this guide’s editorial order. It is not a ranking by market share, quality, or sales. The named devices are examples for comparison, not approved substitutes.

ManufacturerRepresentative device or familyStarting point for buyers
Texas InstrumentsTCAN1042HGVCAN FD and suffix-specific features
NXP SemiconductorsTJA1044, TJA1462CAN FD and signal improvement capability
Infineon TechnologiesTLE9251Automotive CAN FD interface options
Analog DevicesADM3055EIsolated CAN FD with integrated isolated power
Microchip TechnologyMCP2562FDStandby mode and logic-voltage interface
STMicroelectronicsL9616Classical CAN designs
onsemiNCV7344CAN FD, wake-up filters, and package options
ROHM SemiconductorBD41041FJ-C, BD41044FJ-CClassical CAN versus CAN FD selection
Renesas ElectronicsISL72026ASEHRadiation-tolerant aerospace applications
NOVOSENSE MicroelectronicsNCA1042 familyCAN FD and industrial/automotive variants
3PEAKTPT1042 familyIndustrial and automotive ordering choices
ChipanalogCA-IF1042 familyProtected CAN interfaces and variant checks
Elmos SemiconductorE521.21, E521.23CAN integrated into a system basis chip
NVE CorporationIL41050TFDEIsolated CAN FD
Holt Integrated CircuitsHI-3000HHigh-temperature avionics CAN
SIT (芯力特)SIT1042AQCAN FD for vehicle and industrial interfaces

1. Texas Instruments

TI’s TCAN1042 family gives buyers a useful example of why suffixes matter. The family supports classical CAN and CAN FD, but TI distinguishes the data-rate and logic-interface options within its part numbers. In the TCAN1042 family, the G option supports up to 5 Mbps, while V identifies a separate I/O supply for logic-level interfacing.

A quotation that drops a letter from the approved part number may describe a different device. Compare the full ordering code, package, temperature rating, and qualification before accepting it. TI explains these differences on its TCAN1042HGV product .

For an existing BOM, keep the approved manufacturer code intact from the RFQ through the purchase order. Ask the supplier to explain any difference rather than treating a shortened family name as a match.

Eight Pin Chips In Carrier Tape
Eight Pin Chips In Carrier Tape

2. NXP Semiconductors

NXP offers both conventional high-speed CAN interfaces and CAN signal improvement capability (SIC) transceivers. The TJA1044 includes standby operation, while the TJA1462 adds SIC to reduce ringing on the network. NXP specifies the latter for CAN FD communication with higher timing demands.

This makes NXP worth considering when the engineering question involves network topology as well as component availability. A faster transceiver alone does not establish that a particular cable layout, node count, or termination arrangement will work.

NXP describes the TJA1462 as a replacement for specified earlier NXP devices. Buyers should still have engineering confirm the exact variant, pin functions, power states, and board behavior. A manufacturer’s compatibility statement has a defined scope; it should not become a blanket approval for every TJA device.

3. Infineon Technologies

Infineon’s TLE9251 family serves automotive and industrial high-speed CAN networks. Its product selection includes CAN FD devices with different package and logic-interface options. The TLE9251SJ and TLE9251VSJ illustrate how closely related names can distinguish the availability of a VIO connection.

Start by checking whether your controller needs a separate logic supply. Then compare the package drawing against the approved footprint. A small leadless package and an eight-pin leaded package may serve the same communication role but require different assembly arrangements.

For a production purchase, ask for the complete Infineon ordering code, packing format, and current lifecycle information. If the offer covers a different family member, route the change through engineering before placing the order.

4. Analog Devices

Analog Devices is a useful option when the CAN connection needs galvanic isolation. Its ADM3055E combines a CAN FD transceiver, signal isolation, and an isolated DC-to-DC converter in one package. That architecture changes the board’s power and isolation requirements compared with a conventional non-isolated transceiver.

Compare the isolation arrangement before comparing unit cost. A device with integrated isolated power and one that needs a separate isolated supply do not carry the same surrounding BOM. Package clearance, thermal behavior, and emissions also need engineering review.

The official ADM3055E documentation gives the device ratings and approvals. An isolation withstand figure is not the same as a permissible continuous working voltage. Have the design team check the relevant rating and operating conditions for the finished equipment.

Open Control Module And Wiring Harness
Open Control Module And Wiring Harness

5. Microchip Technology

Microchip’s MCP2562FD is a CAN FD transceiver with standby mode and a VIO pin. Its related MCP2561FD uses a SPLIT pin instead. That difference is easy to miss when a supplier lists only the shared family name.

For buyers sourcing alongside a Microchip controller, keep the controller and transceiver as separate BOM decisions. A CAN controller handles protocol functions; the transceiver provides the electrical connection to the bus. Matching the manufacturer does not establish electrical compatibility.

Check the complete package and temperature code, along with any automotive ordering requirements. Microchip notes that automotive-grade versions use special ordering codes. A general product-page description should not replace confirmation of the exact grade being quoted.

6. STMicroelectronics

ST’s L9616 is an automotive high-speed CAN bus transceiver supporting communication up to 1 Mbaud. It is a relevant example for classical CAN applications, particularly when maintaining an established design that already specifies the device.

Its presence in a CAN supplier list should not lead buyers to classify it automatically as a CAN FD option. A manufacturer can offer CAN-related products with substantially different performance and integration levels.

If a repair or production requirement names L9616, check the packing code as well as the device name. ST distinguishes tube and tape-and-reel ordering in its datasheet. For a new CAN FD design, ask engineering to select a device explicitly specified for the required FD operation before requesting quotations.

7. onsemi

The onsemi NCV7344 is a CAN FD transceiver with low-power standby and wake-up through the bus. Its datasheet distinguishes variants by logic-interface connection and wake-up filter behavior. It also lists SOIC and DFN package choices.

Those details make the full part number more useful than a broad description such as “automotive CAN chip.” A change in filter behavior can matter to system wake-up, while a package change can affect assembly and inspection.

Compare the offered variant against the approved datasheet ordering table. For automotive programs, establish the required qualification and production approval documentation before the order. The datasheet’s AEC-Q100 and PPAP statements do not tell you which documents a particular seller can supply with a particular lot.

8. ROHM Semiconductor

ROHM’s BD41041FJ-C and BD41044FJ-C show a clear split between classical CAN and CAN FD. ROHM specifies the BD41041FJ-C for high-speed CAN communication up to 1 Mbps. The BD41044FJ-C is its CAN FD counterpart.

Check those similar part numbers carefully during quotation review. A supplier’s description may look close enough at a glance, yet the distinction changes the intended communication requirements.

Confirm the exact part number, automotive qualification, operating temperature, and packing suffix. ROHM’s BD41041FJ-C listing identifies an SOP-J8 package and tape packaging. Use the manufacturer’s package dimensions rather than assuming every package described informally as “SOIC-8” has the same footprint.

9. Renesas Electronics

Renesas belongs on this list for specialized CAN products, including the ISL72026ASEH radiation-tolerant transceiver. Renesas describes it for satellite and aerospace communication applications and provides listen-mode and loopback functions.

This is a different purchasing task from selecting a general automotive CAN FD device. A high-reliability program may need specific screening, radiation data, package construction, and procurement documentation. An engineering sample and a flight-approved orderable part should never be treated as interchangeable without program approval.

Ask the responsible engineer to define the accepted ordering code and evidence package before sourcing. Also check the interface category carefully: Renesas sells RS-485/422 transceivers too, and those devices cannot be substituted into a CAN requirement simply because their descriptions contain the word “transceiver.”

Leaded Chip In A Protective Tray
Leaded Chip In A Protective Tray

10. NOVOSENSE Microelectronics

NOVOSENSE offers CAN transceivers in its NCA1042 family. Its published selection guides distinguish industrial and automotive variants, including NCA1042-Q1 devices, as well as package choices. The family provides a starting point for buyers evaluating another manufacturer for a CAN FD requirement.

Keep the proposed ordering code tied to a current datasheet. A family comparison can help narrow the search, but it cannot establish that a device matches the approved logic voltage, protection requirements, or operating modes.

When qualifying a new source, request the current English documentation and relevant qualification information for the exact variant. Obtain samples of that variant for engineering evaluation before committing the production BOM. Availability and documentation should be confirmed for the offered lot rather than inferred from a catalog entry.

11. 3PEAK

3PEAK separates industrial and automotive products within its TPT1042 range. Its selector lists TPT1042 and TPT1042V as industrial devices, with TPT1042Q and TPT1042VQ as automotive versions. These are CAN FD transceivers with standby operation.

For purchasing teams, that distinction helps prevent an apparently minor suffix change from becoming an unapproved grade change. Compare the actual pin functions and ratings too; similar naming across manufacturers is not a shared coding standard.

If you are considering 3PEAK as an additional BOM source, have engineering record the approved variant and validation requirements. Once approval is complete, carry its full orderable code into the supplier agreement, including package, qualification, and packing requirements. Avoid purchase orders that allow an unspecified “equivalent” to be shipped.

12. Chipanalog

Chipanalog’s CA-IF1042 family includes protected CAN transceivers for industrial and automotive applications. Its catalog also separates conventional CAN interfaces from isolated CAN products, including devices with integrated isolated power.

The first question is which architecture your board requires. An isolated interface is not an upgrade that can simply be inserted into a non-isolated footprint. Supply connections, package size, isolation spacing, and surrounding components all need review.

Chipanalog publishes cross-reference information, which can help identify candidates for evaluation. Treat a cross-reference as the beginning of a comparison. Before approving a substitute, have engineering compare voltage limits, control pins, propagation timing, wake-up behavior, and protection characteristics against the original part’s requirements.

13. Elmos Semiconductor

Elmos offers CAN functionality within system basis chips (SBCs). Its E521.21 and E521.23 combine a CAN FD interface with power-management functions. The published information distinguishes versions with 3.3 V and 5 V DC-to-DC outputs.

An SBC can therefore affect several BOM lines at once. Replacing it requires review of the regulator, monitoring functions, operating states, and wake-up control in addition to the CAN interface. Comparing it solely with an eight-pin standalone transceiver would miss most of that decision.

Elmos provides an information sheet publicly and lists detailed datasheets on request for these parts. Obtain the full documentation and confirm production and ordering arrangements before designing one in or accepting a supply proposal. A short product summary is insufficient for replacement approval.

Microscope And Packaged Components
Microscope And Packaged Components

14. NVE Corporation

NVE offers isolated CAN devices in the IL41050 range. Its IL41050TFDE listing identifies an isolated CAN FD transceiver rated for 5 Mbps in a wide-body SOIC package. Other IL41050 variants serve different speed and feature requirements.

That makes the suffix particularly important. Older family documentation or a shortened distributor listing can describe a different version from the one being quoted. Use the documentation for the exact orderable device.

For an isolated design, ask engineering to confirm the isolation rating, package spacing, and power-supply arrangement. Signal isolation does not automatically mean the device also generates isolated power. Compare the complete circuit requirements before deciding whether two isolated transceivers are suitable alternatives.

15. Holt Integrated Circuits

Holt’s HI-3000H is a 1 Mbps CAN transceiver aimed at high-temperature avionics applications. Holt lists compatibility with ARINC 825 and gives different temperature ranges for its plastic SOIC and ceramic CERDIP packages.

For this type of purchase, the package and processing flow are part of the requirement. A higher temperature headline does not make two ordering options equivalent, and ceramic and plastic versions can differ in material compliance as well as construction.

Agree the required package, temperature range, screening, and documentation with the program team before seeking stock. Confirm RoHS status for the specific orderable part. Holt’s own table distinguishes compliance between the listed ceramic and plastic options, so a company-wide assumption would be unreliable.

16. SIT (芯力特)

SIT offers CAN, CAN FD, and CAN SIC product categories. Its SIT1042AQ is listed as a CAN FD interface for vehicle and industrial use, supporting up to 5 Mbps with standby operation and remote wake-up. The product page gives SOP8 and DFN package choices.

Buyers should distinguish SIT1042AQ from other SIT1042 variants using the current ordering information. A shared family number does not establish identical logic-interface or protection characteristics.

For a new supplier qualification, request the exact English datasheet, qualification evidence, sample ordering code, and proposed production packaging. Have engineering evaluate the device under the intended network conditions. If the project needs SIC, select an explicitly specified SIC device rather than assuming a CAN FD label includes that capability.

Component Reel And Shielding Bag
Component Reel And Shielding Bag

Conclusion

The most useful CAN transceiver manufacturers shortlist starts with the approved electrical and application requirements. Classical CAN, CAN FD, SIC, isolation, and integrated power management lead to different choices, even when the product descriptions look similar.

Before placing the orderEvidence to confirm
Exact part identityFull manufacturer code, package, grade, and packing suffix
Engineering acceptanceApproved datasheet revision and any substitute validation
Supply routeManufacturer channel confirmation where authorization is required; agreed source documentation otherwise
Offered materialQuantity, lot/date-code details, packaging condition, and current photos where needed
Application documentsRequired qualification, material declarations, screening, or test records for the specific device

Our automotive electronics sourcing covers related component requirements. As an independent supplier, DuoLink Electronics can support component sourcing and BOM quotation, with supply options and documentation confirmed for each inquiry. Send your RFQ with the manufacturer, complete part number, quantity, delivery target, application, and lot or documentation requirements. Any proposed alternative should receive engineering approval before purchase.

Frequently Asked Questions

Which CAN transceiver manufacturers should I compare first?

TI, NXP, Infineon, Microchip, and onsemi provide useful starting points for CAN FD comparisons. Include Analog Devices or NVE when isolation matters, and review specialized Renesas or Holt devices for relevant aerospace requirements. Choose the exact part against your specification.

Can I replace a CAN transceiver with another manufacturer’s eight-pin device?

Only after engineering checks it. Compare the pinout, supply and logic voltages, timing, control modes, protection, package dimensions, and qualification. Matching pin count and nominal data rate is insufficient.

Does a CAN FD transceiver let any CAN controller use CAN FD?

No. The controller must support CAN FD, and the firmware and network configuration must suit the intended operation. The transceiver handles the physical electrical interface; it does not add the missing controller protocol functions.

Does AEC-Q100 qualification mean a device is approved for my automotive project?

No. Confirm the qualification of the exact variant and the project’s additional approval requirements. Customer acceptance, production documentation, and system validation remain separate decisions.

Latest Posts

Server Memory Module And Solid State Drive On An Electronics Workbench
IC Trays And Protective Packaging On An Electronics Workbench
ICs In An ESD Tray Beside Component Storage Shelves
Buyer Reviewing IC Sourcing Requirements
Request A Quote
Contact Us
en_USEnglish

Request a Quote

Send us your part numbers, quantities, or BOM details.Our team will respond with availability, lead time, and pricing.

Contact Us